Commercial Mold Inspection

If the home inspection noted staining, a musty smell, or signs of past leaks, yes — that note is a referral to a specialist. A general inspection is a visual survey of the whole property; a mold inspection measures moisture inside walls, under flooring, and in the attic or crawl space with thermal imaging and moisture meters, and sends air or surface samples to an accredited lab. In San Bernardino the gap shows most in a few places: slab leaks in the postwar homes of the Westside and North End that run for months under carpet or tile, the underbelly of manufactured homes in Muscoy and Arrowhead Farms, groundwater pushing up into slabs on the low valley floor, and the uphill walls of foothill homes below the mountains. A large share of the city's houses have also been rentals with uneven upkeep, which makes past water damage more likely. Book the mold inspection inside your contingency window so the findings can still shape the deal.

Yes, and they are one of the most common sources we find in the city's older homes. Evaporative coolers cool by adding water to the air, which works well in San Bernardino's dry summer heat and badly when something goes wrong. Run during the humid monsoon weather of late summer, or with the house closed so the moist air can't exhaust, a cooler raises indoor humidity to levels where mold grows on closet walls and inside ducts. The unit fails in predictable ways: a corroded pan or float valve leaking onto the roof, a cracked curb seal around the duct opening letting water into the attic, and stagnant water and pads left over winter. Many homes that later added central air kept the cooler duct, which then sweats in summer and admits rain in winter. Staining around the ceiling register beneath the cooler is the sign to look for, and the attic at that opening is where an inspection starts.

They do, because of how they are built underneath. The semi-rural parts of the city — Muscoy, Arrowhead Farms, and parts of Verdemont — and the mobile home parks across San Bernardino hold many manufactured homes, and their plumbing runs through the floor system inside a sealed underbelly wrap. A slow leak there soaks the insulation, and the wrap holds the water against the floor decking out of sight until the floor softens or a musty smell comes through the vents. Skirting traps humid air beneath the home, especially where irrigation or downspouts drain toward it, and older roofs leak at seams, vents, and add-on roofovers. On large semi-rural lots, septic systems and wells add their own moisture near the home. An inspection here goes beneath the home — checking the underbelly for sagging or wet sections, the subfloor at bathrooms and the kitchen, and the ventilation under the floor — rather than stopping at the living areas.

It is worth considering, and the city has hard experience with why. The Old Fire of October 2003 burned through the mountains and foothills above San Bernardino and destroyed hundreds of homes along the city's northern edge, and on Christmas Day that year an intense storm set off debris flows across the burn areas that killed 16 people near San Bernardino. Burned slopes shed water and sediment far faster than vegetated ones for several rainy seasons afterward. Homes at the top of the city, below the slopes beneath the Arrowhead landmark and across the Del Rosa and Verdemont foothills, take that runoff against foundations, garage slabs, and retaining walls. Firefighting water also soaks attics and walls in homes that look untouched, and smoke residue in attics and ducts can hold moisture. After any fire in the range above, a moisture check of the uphill walls, the slab edge, and the attic before the first wet winter is a reasonable precaution.

On the valley floor, the water may be coming from below. Much of downtown and the surrounding low ground sits over the Bunker Hill groundwater basin, formerly swampy land with a documented history of artesian springs and flowing wells, where the water table can sit unusually close to the surface. In wet years that shallow groundwater presses up into slabs and foundations, and slabs poured in the postwar decades rarely included a vapor barrier. The result is moisture migrating through the concrete into carpet pad, under vinyl and laminate, and into the bottom plates of walls — a musty smell, lifting floor tile, or white mineral deposits along the slab edge, with no leak anywhere above. A slab leak in a supply or drain line can look the same, which is why readings matter. Moisture measurements taken across the slab and compared room to room show whether it is general vapor drive from the ground or a concentrated leak a plumber can fix.

The Westside, the North End, and the central tracts are dominated by single-story stucco homes on slabs built in the 1950s and 1960s, and many have been rentals through several ownership changes, with maintenance that varied along the way. The recurring moisture sources are aging galvanized or copper supply lines leaking inside walls or under the slab, cast-iron drains cracking beneath bathrooms and kitchens, original ductwork sweating in attics, roofs re-covered over older layers, and evaporative coolers leaking at their roof curbs. Garage conversions on unsealed slabs and room additions built without permits add hidden moisture paths. The first signs are usually small — a musty closet, a swelling baseboard, a warm spot on the floor from a hot-water slab leak, staining around a ceiling register. A moisture survey of the plumbing walls, the slab perimeter, the attic, and any converted space covers where these houses usually fail, and documents conditions for both owners and tenants.

They can, because monsoon storms deliver a lot of water to buildings that spend most of the year bone-dry. Late-summer thunderstorms build over the mountains and push down into the valley, dropping heavy rain in a short time, often with strong gusts. Water that hits a roof weakened by summer heat, a cracked stucco wall, or a window with failed flashing goes straight into the wall assembly, and runoff off the foothills and across flat lots collects against slab edges and under garage doors. The humidity that comes with the monsoon also slows drying and makes evaporative coolers push moist air into the house. Because the sky clears quickly and the surface dries in hours, it is easy to assume nothing got wet. Wall cavities, attic insulation, and carpet pad stay damp much longer, and mold can start in 24 to 48 hours. A moisture check after any storm that left a stain or a damp spot catches the problem early.